China OEM Enig Pcb - Manufacturer for printed circuit board and pcb design from shenzhen pcb – Yongmingsheng

The shopper satisfaction is our primary focus on. We uphold a consistent level of professionalism, quality, credibility and repair for Manufacturer for printed circuit board and pcb design from shenzhen pcb, To deliver prospects with excellent equipment and providers, and frequently create new machine is our company’s organization objectives. We look forward for your cooperation.
The shopper satisfaction is our primary focus on. We uphold a consistent level of professionalism, quality, credibility and repair for , Our company regards “reasonable prices, efficient production time and good after-sales service” as our tenet. We hope to cooperate with more customers for mutual development and benefits. We welcome potential buyers to contact us.

Goldfinger design in PCB

Goldfinger is an electrical interface. The common packaging form and appearance of PCB are as follows. When the appearance and packaging similar to the figure below are seen in the PCB design, the first reaction is to see them on the boardGold finger.

The easier way for goldfinger to judge is to have both the TOP and BOTTOM of the device

PIN device;It will look like the u-slot in the picture below.

When there is a goldfinger on the board, you need to work on the details of the goldfinger.

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html

Details of goldfinger in PCB:

1) in order to increase the wear resistance of goldfinger, goldfinger usually needs to be plated with hard gold.

2) goldfinger needs chamfering, usually 45°, other angles such as 20°, 30°, etc.

If there is no chamfer in the design, there is a problem.In the figure below, the arrow is 45 degrees

chamfering

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html

The 45° chamfering Angle in PCB is shown in the following figure:

hard gold pcb3

3) goldfinger needs to do the whole block of anti-welding window opening treatment, and the PIN does not need to open the steel net;

4) a minimum distance of 14mil from the tip of finger is required for the sink tin and silver welding pads;Recommended design

When the pad is more than 1mm away from the finger position, including the through hole pad;

5) do not coat goldfinger with copper;

Below is a goldfinger design for reference

hard gold pcb4

6) all layers of the inner layer of goldfinger need to be copper whittled, usually with a width of 3mm;

It can be done with half finger and whole finger.In pci-e design, there are also fingers

Remove all copper from the mingoldfinger area;

Goldfinger’s resistance will be low, and cupping (hollowing out under the finger) will reduce it

The impedance difference between the impedance line and the impedance line is also beneficial to ESD.

Suggestion: cut all the copper under the goldfinger welding pad

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html


HDI basic production process:

A、Brown multilayer circuit board to form Browning film on the surface of copper foil layer, and laser drilling on the surface of copper foil to form laser blind hole

B、 drill the multi-layer circuit board to form a mechanical drill hole

C、 The multi-layer circuit board is coated with copper to form a copper layer in the laser blind hole mechanical drilling, and then the multi-layer circuit board is electroplated to thicken the copper layer in the hole

D、The above multilayer circuit board is made of outer graphics, and the surface treatment of etched screen print resistance welding on the outer layer of graphics electroplating is carried out to obtain the finished HDI board

You May Like:

1、How to identify gold on a pcb

2、PCB what are gold fingers

3、what are gold fingers pcb

4、The main causes of PCB board deformation and rupture


  • China OEM Enig Pcb - Manufacturer for printed circuit board and pcb design from shenzhen pcb – Yongmingsheng Related Video: